Qmark RCC - Cove Heaters Manuale Utente Scaricare il pdf

COVE HEATER

Model D

Read Carefully

- These instructions are written to help you

prevent difficulties that might arise during installation of

heaters. Studying the instructions first may save you con-

siderable time and money later. Observe the following pro-

cedures, and cut your mounting time to a minimum. TO

REDUCE RISK OF FIRE OR ELECTRIC SHOCK:

1. Disconnect all power coming to heater at main service panel

before wiring or servicing.

2. All wiring must be in accordance with the National and Local

Electrical Codes and the heater must be grounded.

3. Verify the power supply voltage coming to heater matches the

ratings printed on the heater nameplate before energizing.

4. This heater is hot when in use. To avoid burns, do not let bare

skin touch hot surfaces.

5. Do not insert or allow foreign objects to enter any ventilation or

exhaust opening as this may cause an electric shock, fire,or

damage to the heater.

6. Do not block air intakes or exhaust in any manner. Keep com-

bustible materials, such as crates, drapes, etc., away from

heater. Do not install behind door, furniture, towels, or boxes.

7. A heater has hot and arcing or sparking parts inside. Do not use

it in areas where gasoline, paint, or flammable liquids are used

or stored.

8. Use this heater only as described in this manual. Any other use

not recommended by the manufacturer may cause fire, electric

shock, or injury to persons.

9. This heater is not approved for use in corrosive atmospheres

such as marine, green house, or chemical storage areas.

Installation & Maintenance Instructions

SAVE THESE INSTRUCTIONS

WARNING

FILE #E21609

Patent Pending

GENERAL

When installing 2 or more heaters along one wall:

1. Mount heaters allowing adequate spacing between heaters as

shown in Table 1.

2. Install optional RCCSPC Splice Plate (if desired) per instructions

provided with RCCSPC.

When mounting heaters end to end add the “maximum allowable

expansion” of each heater and provide that clearance from end to end

of units. See Table 1.

MOUNTING THE HEATER

For 450 to 1200 Watt Heaters:

1. Select correct mounting distance from the ceiling material per

Figure 1. Using Table 1, determine the center to center distance

of the end wall brackets for the particular model (wattage) to be

mounted. Divide this value by 2 to determine the approximate

location to mount the center wall bracket. Mark these locations on

the chosen wall. Locate a stud nearest the center wall bracket

mark. Use this stud for the bracket location. (Disregard original

mark mentioned above) Assemble end wall brackets as shown in

Figure 3.

2. Using the template (provided), align the top of the template with

the ceiling and the center of the pre-punched holes with the

bracket marks on the wall. Choosing the proper ( end or middle)

bracket location holes, mark the bracket pilot hole locations using

the selected pre-punched holes provided on the template. With

the fasteners provided, mount the assembled end wall brackets

and center wall bracket to the wall. Using a tape measure, deter-

mine the distance between the center (slot) of the left end wall

bracket and the hook of the center wall bracket. Add 3-5/8 inches

(92 mm) to this value and record it for center support bracket

location on the cove heater.

3. Orient the cove heater face down on a protective flat surface.

Using the value recorded in step 2, measure this distance from

the left end of the cove heater and mark this location on the back

surface of the panel. Slide the center support bracket to the

marked position on the panel, aligning the center of the bracket

with this mark.

1. THE HEATER MUST BE MOUNTED AT LEAST 6' (182.8 cm) or

(1.83 m ) ABOVE THE FLOOR TO PREVENT ACCIDENTAL CONTACT.

2. TO PREVENT POSSIBLE OVERHEATING OR DAMAGE DUE TO

OVERHEATING, REFER TO FIGURES 1 AND 4 FOR SIDE, TOP,

AND BOTTOM CLEARANCE REQUIREMENTS.

CAUTION

WATTS

MAXIMUM ALLOWABLE MOUNTING SLOT

EXPANSION DISTANCE (CTR-CTR)

450

600

750

900

1050

1200

1500

1800

1/8” (4mm)

1/4” (7mm)

1/2” (13mm)

3/4” (19mm)

7/8” (23mm)

1-1/8 (29mm)

1-3/8 (35mm)

1-1/2” (38mm)

27.75” (705mm)

40.75” (1,035mm)

52.75” (1,340mm)

64.75” (1,645mm)

76.75” (1,949mm)

87.75” (2,229mm)

111.75” (2,838mm)

125.75” (3,194mm)

Table 1

1 2 3 4 5 6 ... 11 12

Sommario

Pagina 1 - COVE HEATER

COVE HEATERModel DRead Carefully- These instructions are written to help youprevent difficulties that might arise during installation ofheaters

Pagina 2

24” (102 mm) MIN. (DRY WALL CEILINGS)6” (152 mm) MIN. (LAY IN OR VINYL CEILINGS OR PLASTIC MOLDING)1“ (25.4 mm) MIN. BETWEEN BOTTOM OF HEATER AN

Pagina 3 - TOTAL LOAD MUST NOT EXCEED

{{Figure 5 – Câblage de l’appareil de chauffageL1L2NL1NoirNoirNoirRougeRougeRougeRouge Rouge RougeBlancBlancBlanc(A) CHAUFFAGES EN 240/208 V (B) CH

Pagina 4 - IMPORTANT INFORMATION

4IMPORTANTES INFORMATIONSGARANTIE LIMITÉETous les produits fabriqués par Marley Engineering Products sont garantis contre les défauts de main d’œuvre

Pagina 5 - GUARDE ESTAS INSTRUCCIONES

24” (102 mm) MIN. (DRY WALL CEILINGS)6” (152 mm) MIN. (LAY IN OR VINYL CEILINGS OR PLASTIC MOLDING)1“ (25.4 mm) MIN. BETWEEN BOTTOM OF HEATER AN

Pagina 6

{{Figure 5. Heater WiringL1L2NL1BlackBlackBlackRedRedRedRed Red RedWhiteWhiteWhite(A) 240 / 208 VOLT HEATERS (B) 120 VOLT OR 277 VOLT HEATERSFOR GROU

Pagina 7

4IMPORTANT INFORMATIONLIMITED WARRANTYAll products manufactured by Marley Engineered Products are warranted against defects in workmanship and materia

Pagina 8 - INFORMACIÓN IMPORTANTE

CALEFACTORESQUINERO DE TECHOModelo DLea cuidadosamente – Estas instrucciones están escritas para ayudarle asuperar las dificultades que podrían aparec

Pagina 9 - CONSERVEZ CES INSTRUCTIONS

24” (102 mm) MIN. (DRY WALL CEILINGS)6” (152 mm) MIN. (LAY IN OR VINYL CEILINGS OR PLASTIC MOLDING)1“ (25.4 mm) MIN. BETWEEN BOTTOM OF HEATER AN

Pagina 10 - TOP VIEW

{{Figura 5. Cableado del calefactorL1L2NL1NegroNegroNegroRojoRojoRojoRojo Rojo RojoBlancoBlancoBlanco(A) CALEFACTORES DE 240 / 208 VOLTS (B) CALEFACT

Pagina 11 - LA CHARGE TOTALE DE TOUS LES

4INFORMACIÓN IMPORTANTEGARANTÍA LIMITADATodos los productos fabricados por Marley Engineered Products están garantizados contra defectos en manufactur

Pagina 12 - IMPORTANTES INFORMATIONS

APPAREIL DECHAUFFAGE ENCASTRÉModèle DÀ lire attentivement – Ces instructions sont écrites pour vous aider à éviterles difficultés qui pourraient surve

Commenti su questo manuale

Nessun commento

Qmark RCC - Cove Heaters Manuale Utente

Navigare online o scaricare Manuale Utente per Radiatori Qmark RCC - Cove Heaters. Qmark RCC - Cove Heaters User Manual Manuale Utente

Sommario

Commenti su questo manuale

Prodotti e manuali riguardandi Radiatori Qmark RCC - Cove Heaters