Dear Owner,
Congratulations! Thank you for purchasing this new heater by Marley Engineered Products. You have made a wise invest-
ment selecting the highest quality product in the heating industry. Please carefully read the installation and maintenance
instructions shown in this manual. You should enjoy years of efficient heating comfort with this product from Marley
Engineered Products... the industry’s leader in design, manufacturing, quality and service.
... The Employees of Marley Engineered Products
Installation & Maintenance Instructions
Read Carefully - These instructions are written to help you prevent
difficulties that might arise during installation of heaters. Studying
the instructions first may save you considerable time and money
later. Observe the following procedures and cut your installation
time to a minimum. Failure to follow these instructions may lead to
fire, electric shock, personal injury, property damage or product fail-
ure.
1. This radiant heater is a component of the complete heating sys-
tem. The heating system designer must consider the risks asso-
ciated with its operation and specify adequate controls and safe-
ty devices. Where the consequences of failure could result in
personal injury, property damage or fire, back-up controls are
essential.
2. Read all instructions before using the heater.
3. Do NOT use this heater as a residential or household heater.
4. This heater is hot when in use. To avoid burns, do not let bare
skin touch hot surfaces. If used as a portable heater, keep com-
bustible materials, such as furniture and papers at least 5 feet
from the front of the heater.
5. Always disconnect the heater when not in use.
6. To prevent possible electrical shock, disconnect ALL power
coming to heater at main service panel before wiring or
servicing.
7. All wiring must be in accordance with the National and Local
Electrical Codes and the heater must be grounded as a
precaution against possible electrical shock.
8. Verify the power supply voltage coming to the heater matches
the ratings printed on the heater nameplate before energizing.
9. This heater is NOT suitable for use in hazardous locations as
described by the National Fire Protection Association (NFPA).
This heater has hot and arcing or sparking parts inside. DO NOT
use in areas where gasoline, paint or other flammable liquids are
used or stored.
10. In order to prevent fire, electric shock, injury to persons and
equipment damage, protect with a ground fault device (GFCI or
GFI) such as Marley Engineered Products WMGF240 for 240V
heaters and WMGF480 for 480 volt heaters.
11. This heater is intended for Ceiling Installation ONLY (except as
noted below.). The following clearances MUST be maintained:
a) Top of heater to ceiling - 24" (640 mm)
b) Bottom of heater to floor - 10' (3048 mm)
c) Side of heater to wall - 36" (914 mm)
d) End of heater to wall - 36" (914 mm)
e) Side of heater to side of adjacent heater - 36" (914 mm)
f) End of heater to end of adjacent heater - 36" (914 mm)
12. Heater MUST be securely fastened to the building structure to
prevent it from falling.
13.DO NOT stack or store combustible materials in the radiation
path under the heater, or in the space a distance of 5 feet from
any projected edge of the heater.
14. Under special controlled conditions this heater may be
converted for use as a movable heater by installation of the
optional Portable Cart Kit, Cord Kits, Grille Kit and Tip Over Kits.
Extreme care must be taken when using this heater as a
movable unit! The heater operates at very high
temperatures and could cause a fire if placed too close to
combustible materials. NEVER OPERATE THIS HEATER AS
A MOVABLE UNIT WHILE UNATTENDED. Always maintain at
least the minimum clearances as stated above. If the Tip Over
Kit is not provided, the heater could cause a fire if it falls over.
15. If used as a cord connected movable heater, always make sure
the outlet or power source to which the heater is connected is
properly grounded. Use of the heater with an extension cord is
not recommended. If one must be used, it must be provided
with a grounding conductor and must be rated to handle a load
of at least 125% of the maximum heater ampere load. Always
inspect the cord for damage before each use and do not use if
damaged. Route cord so it is not subject to being damaged
during use.
16. Use this heater only as described in this manual. Any other use
not recommended by the manufacturer may cause fire, electric
shock or injury to persons.
WARNING
M Series
Fixed Overhead Radiant Heaters
SAVE THESE INSTRUCTIONS
Commenti su questo manuale